Sun-microsystems SERVER 1290 Manual do Utilizador descarregar pdf (Página 72)

60 Netra 1290 Server Installation Guide • May 2006

FIGURE A-6 RJ-45 Serial Connectors

Note – Serial port B is reserved.

TABLE A-8 lists the settings needed to use the LOM Serial A connection. The

configuration of this port cannot be changed. Be sure to check the manufacturer’s

documentation for your specific terminal server. Communication on LOM Serial A is

subject to interruption by the LOM device. Refer to the Netra 1290 Server System

Administration Guide, 819-4374.

TABLE A-7 RJ-45 Serial Connector Pinout

Pin Signal

1RTS

2 DTR

3 TXD

4 Signal Ground

5 Signal Ground

6 RXD

7 DSR

8 CTS

TABLE A-8 Default Settings for Connecting to LOM Serial A

Parameter Setting

Connector LOM Serial A

Rate 9600 baud

Parity No

Stop bits 1

Data bits 8

LOM Serial A

Serial B

1818

1 2 ... 67 68 69 70 71 72 73 74 75 76

1290 Server Installation 1
Contents 3
Using UNIX Commands 9
Shell Prompts 10
Typographic Conventions 10
Related Documentation 11
Third-Party Web Sites 11
Sun Welcomes Your Comments 12
Unpacking the Server 13
Shipping kit 14
Opening the Shipping Carton 14
Carton protection pads 14
6. Remove the outer carton 15
Installing Slide Rails 16
FIGURE 1-3): 17
FIGURE 1-4) 18
Spring Clips and Cutouts 19
FIGURE 1-3) 20
FIGURE 1-6) 22
900 Cabinet 23
Rear bracket 24
Front bracket 24
Post Cabinet 25
Post Rack 26
FIGURE 1-8) 27
FIGURE 1-9) 28
(FIGURE 1-11) 30
Aligning the Rails 31
Inner rails 31
Outer rails 31
Removing the Shipping Cradle 32
Securing screw Securing screw 33
To Install the Lock Nuts 34
FIGURE 1-16) 35
Serial A Serial B 36
SSC1 SSC1 36
To Install the CMA–Lite 37
To Install the CMA–800 38
FIGURE 1-20 and FIGURE 1-21 39
Upper pivot bracket 40
Hinge pin 40
Upper CMA arm 40
Lower pivot bracket 41
Lower CMA arm 41
Slide rail 42
Left hand T-bracket 42
Right hand T-bracket 43
FIGURE 1-25) 44
Connecting Power Cables 45
Controller 46
FIGURE 1-26) 47
Connecting the I/O Assemblies 49
Setting Up 51
Setting Up the Hardware 52
On/Standby Switch 52
Powering On the Server 53
■ From the LOM port 54
■ By the On/Standby switch 54
# shutdown -i5 55
Do you want to continue? [no] 55
Setting Up the Server 56
Enter new password: 57
Enter new password again: 57
Operating System 58
Packages 59
To Install the LOM Drivers 60
To Install the LOM Utility 62
Chapter 2 Setting Up 51 63
Netra 1290 Server Connections 65
PCI+ IB_SSC Assemblies 66
SCSI Connector 67
Alarms Port 68
NET0/NET1 Ethernet Ports 69
1 TRD0_H 5 TRD2_L 70
2 TRD0_L 6 TRD1_L 70
3 TRD1_H 7 TRD3_H 70
4 TRD2_H 8 TRD3_L 70
■ Category 4 (STP-4) 71
RJ-45 Serial Connectors 72
RJ-45 Serial Connector Pinout 72
LOM Serial A 72
Serial B 72
TABLE A-9 lists the pin 73

Comentários a estes Manuais

Sem comentários

Sun-microsystems SERVER 1290 Manual do Utilizador Página 72

Comentários a estes Manuais

Manuais e produtos relacionados com Computadores Sun-microsystems SERVER 1290